Electrical Panel Upgrades in Burlington: 100A to 200A Service
Burlington 100A to 200A service upgrades and panel replacements, with Burlington Hydro coordinating the disconnect and reconnect.
- Burlington Hydro coordination included
- Same-Week Scheduling
- ESA permit and inspection included
- Aldershot
- Roseland
- Alton Village
- ECRA/ESA Licensed
- ESA Permit Included on Every Job
- Same-Week Scheduling
- WSIB Certified
- Free Written Itemised Quote
When Do You Need an Electrical Panel Upgrade in Burlington?
Eight triggers account for almost every panel upgrade we quote in Burlington. If one of these describes your property, the load calculation will tell you how far the existing service can stretch.
Home insurance refusal or a renewal notice
Toronto underwriters decline or surcharge policies on homes still running an obsolete 60A service or a fuse block. The ESA Certificate of Inspection is what closes the file.
Level 2 EV charger installation at 40A or 50A
An EV charger is a continuous load. Added to laundry, HVAC and refrigeration on an aged 100A panel, the OESC Section 8 calculation runs out of room fast.
Heat pump or central air conversion
Moving off gas heating to a cold-climate heat pump needs dedicated high-amperage breakers and headroom the original panel was never sized for.
Legal basement suite or accessory dwelling unit
City of Toronto secondary-suite permits require a documented load calculation, a dedicated subpanel and a separate disconnect for the suite.
Screw-in glass fuses or cartridge fuse blocks
Fuse blocks cannot provide the arc-fault and ground-fault protection the Ontario Electrical Safety Code now expects on modern branch circuits.
Flickering lights when appliances start
That flicker is voltage drop under load. It points at bus-bar saturation or loose terminations at the main breaker, both end-of-life signals.
Doubled-up breakers with no knockouts left
When every position is tandemmed and the enclosure has no knockouts left, adding a circuit safely means a new load centre, not more stacking.
Corroded service mast or meter base
A weathered mast and weatherhead lets water track into the panel interior. The service entrance conductors and meter base get replaced with the panel.
Panel Upgrade Services in Burlington
Burlington 100A to 200A service upgrades and panel replacements, with Burlington Hydro coordinating the disconnect and reconnect.
Burlington Hydro handles the disconnect and reconnect for Burlington addresses. We file the ESA Notification of Work, book the utility window, complete the install, and hand over the Certificate of Inspection.
Most Requested 100A to 200A Service Upgrades
Upgrade an undersized 100A service to a 200A, 42-circuit panel with Toronto Hydro disconnect and reconnect coordinated on the day.
View service
Insurance Deadlines Fuse Box Replacement
Convert an outdated 60A fuse panel to a modern breaker panel with AFCI/GFCI protection and an ESA certificate your insurer accepts.
View service
Resale Blocker Federal Pacific Stab-Lok Panel Replacement
Replace a defective Federal Pacific / Federal Pioneer Stab-Lok panel flagged at inspection with a code-compliant breaker panel and ESA certificate.
View serviceHow Your Burlington Panel Upgrade Works
The Burlington Hydro coordination process for Burlington addresses, step by step.
- 01
Service layout approval
We submit the new service layout, conductor sizing and meter base position so the utility can confirm the point of attachment before any material is ordered.
- 02
Disconnect scheduling
Once the ESA Notification of Work is filed, we book the disconnect slot. Morning slots let us finish and re-energize inside the same working day.
- 03
Meter pull and service change
The utility pulls the meter and drops the service. We replace the meter base, service entrance conductors, mast or lateral, and the load centre.
- 04
ESA inspection
The ESA inspector attends, reviews bonding, grounding, terminations and labelling, and signs off the Certificate of Inspection.
- 05
Energization and handoff
The utility reconnects and sets the meter. You get the certificate, the panel schedule and the itemised invoice matching the original quote.
Booking a panel upgrade in Burlington?
Burlington Hydro coordination, ESA permit and final inspection are included in the written quote, backed by our Satisfaction Guaranteed promise.
Why Burlington Owners Call Us
-
Burlington Hydro disconnect and reconnect coordinated directly
-
Panel-only specialists, so the service entrance work is routine
-
OESC Section 8 load calculation before any quote
-
ESA permit and final inspection included on every job
Getting to Burlington Panel Jobs
Burlington sits at the western edge of our 50km radius, reached along the QEW and Highway 403 through Aldershot and Roseland. Burlington Hydro is the distribution utility, and we book the disconnect and reconnect through them before confirming the install date.
Burlington Housing Stock We Work On
Aldershot and Roseland carry post-war detached homes on 100A services with original panels and, in places, aluminum branch wiring. Alton Village and the newer north-end subdivisions are 200A builds where subpanels and EV circuits are the usual scope.
Burlington Housing Stock and Seasonal Notes
Burlington sits at the western edge of our service radius, which affects scheduling more than pricing. Aldershot and Roseland carry post-war detached homes on 100A services with original panels and, in the late 1960s stock, aluminum branch wiring that surfaces in autumn insurance reviews. Alton Village and the north-end subdivisions are 200A builds where garage subpanels, workshop circuits and EV charging are the usual scope.
Burlington Hydro handles the disconnect and reconnect. Because we travel further for these jobs, we group Burlington and Oakville work into the same days where possible, which means the assessment is same-week but the install date may sit inside a specific window rather than being fully flexible. We tell you that window up front.
Garage and workshop subpanels are the most common Burlington request, and they have no utility dependency at all, so those jobs typically complete within a week of the quote being accepted.
Neighbourhoods We Cover in Burlington
- Aldershot
- Roseland
- Alton Village
Local service facts
- Distribution utility
- Burlington Hydro
- Municipality
- City of Burlington
- Scheduling
- Same-Week Scheduling
- ESA permit
- Included
What Burlington Customers Say
Panel upgrades and service entrance work in this area.
Post-war home on 100A with the original panel. Moved to 200A, new meter base, and the Burlington Hydro reconnect was handled without us chasing anyone.
Needed a subpanel in the garage for a workshop and charger. Sized, installed and inspected inside a week.
Panel Upgrade FAQs for Burlington
Do you cover Burlington for panel upgrades?
Yes. Burlington sits at the western edge of our 50km GTA service radius, including Aldershot, Roseland, Alton Village and the downtown core.
Which utility handles a Burlington panel upgrade?
Burlington Hydro is the distribution utility for Burlington, and the disconnect and reconnect is booked through them.
Can you add a garage subpanel in Burlington?
Yes. A garage or workshop subpanel runs on a correctly sized feeder with isolated neutral and ground, and covers charger, tool and lighting loads. Subpanel installations run $800 to $3,000 CAD.
What does a panel upgrade cost in Burlington?
A 100A to 200A upgrade runs $2,500 to $8,000 CAD, with the ESA permit fee and utility coordination fee broken out in the written quote.
Does being at the edge of your service area cost more?
No. Travel is not billed as a separate line inside our 50km radius. What it affects is scheduling: we group Burlington and Oakville work into the same days where practical, so the install date sits inside a specific window rather than being fully flexible. We state that window before you accept.
Can you add a workshop subpanel without a service upgrade?
Usually yes. Where the demand calculation shows headroom on your existing service, a garage or workshop subpanel on a correctly sized four-wire feeder covers tool, lighting and charger loads for $800 to $3,000 CAD, with no utility disconnect required.
Still have a question?
Ask the crew directly. We answer load calculation, permit and utility coordination questions before you commit to anything.
Nearby Areas We Also Cover
Crews working near Burlington also handle panel upgrades in these areas.
Need an Electrical Panel Upgrade in Burlington?
Same-Week Scheduling for the on-site assessment, with Burlington Hydro disconnect and reconnect coordinated for you.
- ESA permit and final inspection included
- Toronto Hydro coordination handled
- No hidden fees on the written quote
Thanks, we have your request.
A licensed crew member will be in touch to book the on-site estimate.
Request a Written Itemised Quote
Four fields. We reply with a free on-site estimate date and the ESA permit and coordination fees broken out separately.